| (a) Applicability. Except as specified in §115.471 of this title (relating to Exemptions), the requirements in this division apply to the owner or operator of a manufacturing operation using adhesives or adhesive primers for any of the application processes specified in §115.473(a) of this title (relating to Control Requirements) in the Dallas-Fort Worth and Houston-Galveston-Brazoria areas, as defined in §115.10 of this title (relating to Definitions). Adhesives or adhesive primers applied in the field (e.g., construction jobs in the field) are not subject to this division. (b) Definitions. Unless specifically defined in the Texas Clean Air Act (Texas Health and Safety Code, Chapter 382) or in §§3.2, 101.1, or 115.10 of this title (relating to Definitions), the terms in this division have the meanings commonly used in the field of air pollution control. In addition, the following meanings apply in this division unless the context clearly indicates otherwise. (1) Acrylonitrile-butadiene-styrene or ABS welding--Any process to weld acrylonitrile-butadiene-styrene pipe. (2) Adhesive--Any chemical substance applied for the purpose of bonding two surfaces together other than by mechanical means. (3) Adhesive primer--Any product intended by the manufacturer for application to a substrate, prior to the application of an adhesive, to provide a bonding surface. (4) Aerosol adhesive or adhesive primer--An adhesive or adhesive primer packaged as an aerosol product in which the spray mechanism is permanently housed in a non-refillable can designed for handheld application without the need for ancillary hoses or spray equipment. (5) Aerospace component--Any fabricated part, processed part, assembly of parts, or completed unit of any aircraft including but not limited to airplanes, helicopters, missiles, rockets, and space vehicles. This definition includes electronic components. (6) Application process--A series of one or more application systems and any associated drying area or oven where an adhesive or adhesive primer is applied, dried, or cured. An application process ends at the point where the adhesive is dried or cured, or prior to any subsequent application of a different adhesive. It is not necessary for an application process to have an oven or flash-off area. (7) Application system--Devices or equipment designed for the purpose of applying an adhesive or adhesive primer to a surface. The devices may include, but are not be limited to, brushes, sprayers, flow coaters, dip tanks, rollers, and extrusion coaters. (8) Ceramic tile installation adhesive--Any adhesive intended by the manufacturer for use in the installation of ceramic tiles. (9) Chlorinated polyvinyl chloride plastic or CPVC plastic welding--A polymer of the vinyl chloride monomer that contains 67% chlorine and is normally identified with a chlorinated polyvinyl chloride marking. (10) Chlorinated polyvinyl chloride welding or CPVC welding--An adhesive labeled for welding of chlorinated polyvinyl chloride. (11) Contact adhesive--An adhesive: (A) designed for application to both surfaces to be bonded together; (B) allowed to dry before the two surfaces are placed in contact with each other; (C) forms an immediate bond that is impossible, or difficult, to reposition after both adhesive-coated surfaces are placed in contact with each other; (D) does not need sustained pressure or clamping of surfaces after the adhesive-coated surfaces have been brought together using sufficient momentary pressure to establish full contact between both surfaces; and (E) does not include rubber cements that are primarily intended for use on paper substrates or vulcanizing fluids that are designed and labeled for tire repair only. (12) Cove base--A flooring trim unit, generally made of vinyl or rubber, having a concave radius on one edge and a convex radius on the opposite edge that is used in forming a junction between the bottom wall course and the floor or to form an inside corner. (13) Cove base installation adhesive--Any adhesive intended by the manufacturer to be used for the installation of cove base or wall base on a wall or vertical surface at floor level. (14) Cyanoacrylate adhesive--Any adhesive with a cyanoacrylate content of at least 95% by weight. (15) Daily weighted average--The total weight of volatile organic compounds (VOC) emissions from all adhesives or adhesive primers subject to the same VOC content limit in §115.473(a) of this title (relating to Control Requirements), divided by the total volume of those adhesives or adhesive primers (minus water and exempt solvent) delivered to the application system each day. Adhesives or adhesive primers subject to different emission standards in §115.473(a) of this title must not be combined for purposes of calculating the daily weighted average. In addition, determination of compliance is based on each adhesive or adhesive primer application process. (16) Ethylene propylenediene monomer (EPDM) roof membrane--A prefabricated single sheet of elastomeric material composed of ethylene propylenediene monomer and that is field-applied to a building roof using one layer or membrane material. (17) Flexible vinyl--Non-rigid polyvinyl chloride plastic with a 5.0% by weight plasticizer content. (18) Indoor floor covering installation adhesive--Any adhesive intended by the manufacturer for use in the installation of wood flooring, carpet, resilient tile, vinyl tile, vinyl-backed carpet, resilient sheet and roll, or artificial grass. Adhesives used to install ceramic tile and perimeter-bonded sheet flooring with vinyl backing onto a non-porous substrate, such as flexible vinyl, are excluded from this definition. (19) Laminate--A product made by bonding together two or more layers of material. (20) Metal to urethane/rubber molding or casting adhesive--Any adhesive intended by the manufacturer to bond metal to high density or elastomeric urethane or molded rubber materials, in heater molding or casting processes, to fabricate products such as rollers for computer printers or other paper handling equipment. (21) Motor vehicle adhesive--An adhesive, including glass-bonding adhesive, used in a process that is not an automobile or light-duty truck assembly coating process, applied for the purpose of bonding two vehicle surfaces together without regard to the substrates involved. (22) Motor vehicle glass-bonding primer--A primer, used in a process that is not an automobile or light-duty truck assembly coating process, applied to windshield or other glass, or to body openings, to prepare the glass or body opening for the application of glass-bonding adhesives or the installation of adhesive-bonded glass. Motor vehicle glass-bonding primer includes glass-bonding/cleaning primers that perform both functions (cleaning and priming of the windshield or other glass, or body openings) prior to the application of adhesive or the installation of adhesive-bonded glass. (23) Motor vehicle weatherstrip adhesive--An adhesive, used in a process that is not an automobile or light-duty truck assembly coating process, applied to weatherstripping materials for the purpose of bonding the weatherstrip material to the surface of the vehicle. (24) Multipurpose construction adhesive--Any adhesive intended by the manufacturer for use in the installation or repair of various construction materials, including but not limited to drywall, subfloor, panel, fiberglass reinforced plastic (FRP), ceiling tile, and acoustical tile. (25) Outdoor floor covering installation adhesive--Any adhesive intended by the manufacturer for use in the installation of floor covering that is not in an enclosure and that is exposed to ambient weather conditions during normal use. (26) Panel installation--The installation of plywood, pre-decorated hardboard or tileboard, fiberglass reinforced plastic, and similar pre-decorated or non-decorated panels to studs or solid surfaces using an adhesive formulated for that purpose. (27) Perimeter bonded sheet flooring installation--The installation of sheet flooring with vinyl backing onto a nonporous substrate using an adhesive designed to be applied only to a strip of up to four inches wide around the perimeter of the sheet flooring. (28) Plastic solvent welding adhesive--Any adhesive intended by the manufacturer for use to dissolve the surface of plastic to form a bond between mating surfaces. (29) Plastic solvent welding adhesive primer--Any primer intended by the manufacturer for use to prepare plastic substrates prior to bonding or welding. (30) Plastic foam--Foam constructed of plastics. (31) Plastics--Synthetic materials chemically formed by the polymerization of organic (carbon-based) substances. Plastics are usually compounded with modifiers, extenders, or reinforcers and are capable of being molded, extruded, cast into various shapes and films, or drawn into filaments. Cont'd... |
