| (D) Motor vehicle gasket/sealing material--A fluid
used in a process that is not an automobile or light-duty truck manufacturing
coating process and is applied to coat a gasket or replace and perform
the same function as a gasket. Automobile and light-duty truck gasket/gasket
sealing material includes room temperature vulcanization seal material.
(E) Motor vehicle lubricating wax/compound--A protective
lubricating material used in a process that is not an automobile or
light-duty truck manufacturing coating process and is applied to vehicle
hubs and hinges.
(F) Motor vehicle sealer--A high viscosity material
used in a process that is not an automobile or light-duty truck manufacturing
coating process and is generally, but not always, applied in the paint
shop after the body has received an electrodeposition primer coating
and before the application of subsequent coatings (e.g., primer-surfacer).
The primary purpose of motor vehicle sealer is to fill body joints
completely so that there is no intrusion of water, gases, or corrosive
materials into the passenger area of the body compartment. Such materials
are also referred to as sealant, sealant primer, or caulk.
(G) Motor vehicle trunk interior coating--A coating
used in a process that is not an automobile or light-duty truck manufacturing
coating process and is applied to the trunk interior to provide chip
protection.
(H) Motor vehicle underbody coating--A coating used
in a process that is not an automobile or light-duty truck manufacturing
coating process and is applied to the undercarriage or firewall to
prevent corrosion or provide chip protection.
(7) Paper, film, and foil coating--The coating of paper
and pressure-sensitive tapes (regardless of substrate and including
paper, fabric, and plastic film), related web coating processes on
plastic film (including typewriter ribbons, photographic film, and
magnetic tape), metal foil (including decorative, gift wrap, and packaging),
industrial and decorative laminates, abrasive products (including
fabric coated for use in abrasive products), and flexible packaging.
(A) Paper, film, and foil coating includes the application
of a continuous layer of a coating material across the entire width
or any portion of the width of a paper, film, or foil web substrate
to:
(i) provide a covering, finish, or functional or protective
layer to the substrate;
(ii) saturate the substrate for lamination; or
(iii) provide adhesion between two substrates for lamination.
(B) Paper, film, and foil coating excludes coating
performed on or in-line with any offset lithographic, screen, letterpress,
flexographic, rotogravure, or digital printing press; or size presses
and on-machine coaters that function as part of an in-line papermaking
system.
(8) Pleasure craft--Any marine or fresh-water vessel
used by individuals for noncommercial, nonmilitary, and recreational
purposes that is less than 65.6 feet in length. A vessel rented exclusively
to, or chartered for, individuals for such purposes is considered
a pleasure craft.
(A) Antifoulant coating--A coating applied to the underwater
portion of a pleasure craft to prevent or reduce the attachment of
biological organisms, and registered with the United States Environmental
Protection Agency as a pesticide under the Federal Insecticide, Fungicide,
and Rodenticide Act (7 United States Code, §136).
(B) Antifoulant sealer/tie coating--A coating applied
over an antifoulant coating to prevent the release of biocides into
the environment or to promote adhesion between an antifoulant coating
and a primer or other antifoulants.
(C) Extreme high-gloss coating--A coating that achieves
at least 90% reflectance on a 60 degree meter when tested by American
Society for Testing and Materials Method D523-89.
(D) Finish primer-surfacer--A coating applied with
a wet film thickness less than 10 mils prior to the application of
a topcoat for purposes of providing corrosion resistance, adhesion
of subsequent coatings, a moisture barrier, or promotion of a uniform
surface necessary for filling in surface imperfections.
(E) High-build primer-surfacer--A coating applied with
a wet film thickness of 10 mils or more prior to the application of
a topcoat for purposes of providing corrosion resistance, adhesion
of subsequent coatings, or a moisture barrier, or promoting a uniform
surface necessary for filling in surface imperfections.
(F) High-gloss coating--A coating that achieves at
least 85% reflectance on a 60 degree meter when tested by American
Society for Testing and Materials Test Method D523-89.
(G) Pleasure craft coating--A marine coating, except
unsaturated polyester resin (fiberglass) coatings, applied by brush,
spray, roller, or other means to a pleasure craft.
(H) Pretreatment wash primer--A coating that contains
no more than 25% solids by weight and at least 0.10% acids by weight;
used to provide surface etching; and applied directly to fiberglass
and metal surfaces to provide corrosion resistance and adhesion of
subsequent coatings.
(I) Repair coating--A coating used to re-coat portions
of a previously coated product that has sustained mechanical damage
to the coating following normal surface coating processes.
(J) Topcoat--A final coating applied to the interior
or exterior of a pleasure craft.
(K) Touch-up coating--A coating used to cover minor
coating imperfections appearing after the main surface coating process.
|
